Home
Shop
Wishlist0

Raspberry Pi Pico Pre-Solder Header with Type-C USB

600.00 EGP

Buy Now
Availability: In Stock
SKU:3496300073092

A small Raspberry Pi Pico module with Raspberry ‘s own RP2040 microcontroller made in the UK. RP2040 is a dual core chip based on ARM Cortex M0+ clocked at 133 MHz. The module has 264 kB of SRAM memory and 2 MB of Flash memory. The chip features 26 GPIO pins that operate at 3.3 V and a temperature sensor. Raspberry Pi Pico is programmed in C/C++ via Type-C USB connector.

Product description: Raspberry Pi Pico – RP2040 ARM Cortex M0+

A compact Raspberry Pi Pico module with Raspberry‘s own RP2040 microcontroller made in the UK. The RP2040 is a dual core ARM Cortex M0+ based chip clocked at 133 MHz. The module has 264 kB of SRAM memory and 2 MB of Flash memory. The chip features 26 GPIO pins that operate at 3.3 V and a temperature sensor. Raspberry Pi Pico is programmed in C/C++ language, via Type-C USB connector.

Pinouts of Raspberry Pi Pico module

The Raspberry Pi Pico module is equipped with 26 GPIO pins, which include: 2x SPI, 2x I2C, 2x UART, 3x ADC 12-bit, 16x PWM. An additional 8 IO (PIO) pins are provided to support custom peripherals.

Power supply for Raspberry Pi Pico

The Type-C connector is used to power and communicate the Raspberry Pi Pico board with the computer. A 5 V power supply is required for the module to work properly. The board can also be powered from VSYS pin with 1.8 V to 5.5 V  using e.g. 3.7 V Li-Pol battery or 3x AA battery.

The logic part of the Raspberry Pi Pico operates at 3.3 V.

picow pinout

The pin layout of the Raspberry Pi Pico.

Programming the Raspberry Pi Pico

Raspberry Pi Pico is programmed in C/C++ or MicroPython. To upload a program to the board, press and hold the BOOTSEL button and connect the Raspberry Pi Pico to the computer via a Type-C USB cable. The module will be detected as a USB mass storage device named RPI-RP2, the program file should be dragged and dropped in the RPI-RP2 volume. The manufacturer provides an SDK repository for the C language.

First steps with MicroPython

The Raspberry Pi Pico can be programmed by connecting it to a computer via USB cable by dragging and dropping a file. A downloadable UF2 file has been prepared to help you get started with MicroPython.

  • Download the MicroPython UF2 file.
  • Press and hold the BOOTSEL button and connect the board to the USB port of your Raspberry Pi or computer.
  • Release the BOOTSEL button once the Pico is connected to your computer.
  • The Raspberry Pi Pico will be mounted as a storage device with the RPI-RP2 volume.
  • Drag and drop the MicroPython UF2 file onto the RPI-RP2 volume.
  • Pico will restart, now MicroPython will be used.
  • You can access the REPL and MicroPython through the serial USB port.
Pierwsze kroki z MicroPython
Hello World in C/C++

The first program written by any programmer is “Hello World”, in this case via the Raspberry Pi 4B’s USB serial port.

  • Download the UF2 “Hello World” file.
  • Press and hold the BOOTSEL button and connect the Raspberry Pi Pico to the Raspberry Pi USB port.
  • The board will be mounted as a storage device with the RPI-RP2 volume.
  • Drag and drop the UF2 file into the RPI-RP2 volume.
  • Pico will restart.
  • Open a terminal on the Raspberry Pi 4B and run the commands:
    1. sudo apt install minicom
    2. minicom 115200 /dev/ttyACM0
  • You should see “Hello World” written out in the terminal window.
Download the UF2 file.

Check the code.

Hello World w C
Raspberry Pi Pico specifications
PARAMETER VALUE
Chip Raspberry Pi RP2040
Core ARM Cortex-M0+ Dual-Core 133 MHz
SRAM 264 kB
Flash memory 2 MB
Pinouts 40-pin / 23 GPIO digital + 3 ADC pins
Interfaces 2x UART, 2x I2C, 2x SPI, up to 16 PWM channels
Supply voltage 5 V (USB)
Operating voltage of the logic part 3,3 V
Power supply / data transmission connector Type-C USB
Dimensions 51 x 21 mm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Back to Top
Product has been added to your cart