Home
Shop
Wishlist0

E72-2G4M20S1E CC2652P Wireless ZigBee 3.0 ad hoc network Module 2.4Ghz 20dBm SoC

  • [Chip solution]: CC2652P
  • [Carrier frequency]: 2.400~2.480GHz
  • [Transmission power]: 20dBm
  • [Communication distance]:700m
  • [Product size]:17.5*28.7*2.5mm
  • [Introduction]: Link72(E72-2G4M20S1E )is a ZigBee3.0 ad hoc network wireless module based on CC2652P produced by TI as the core and independently developed by Ebyte. The transmit power is 20dBm. It integrates an ARM microcontroller and a high-performance wireless transceiver inside 48MHz high precision low temperature drift crystal oscillator

950.00 EGP

Buy Now
Availability: In Stock
SKU:34963000865810
Specifications

E72-2G4M20S1E/Link72 CC2652P Wireless ZigBee 3.0 ad hoc network Module

Parameters
Hardware
parameters
parameter value Remark
SoC CC2652P1FRGZ      Texas Instruments
kernel Arm ® Cortex ® -M4F Ultra low power consumption
FLASH 352 KB      –
RAM 80 KB      –
Crystal frequency 48MHz/32.768KHz   External crystal
Size 17.5*28.7*2.5 mm width * length * height
Antenna form PCB Onboard Antenna  Equivalent impedance is about 50 Ω
Communication
Interface
UART 2 -wire serial port, baud rate: 230400 (only
supported)
Packaging method SMD Stamp half hole, hole spacing 1.27mm
Product Weight 1.9±0.1g     –
Electrical
parameters
minimum Typical
value
maximum
value
unit condition
voltage 1.9 3.3 3.8 V More than 3.8V permanently burns the module
communication level 3.3 V Using 5.0V TTL is recommended to add
level conversion
Emission current 106 mA Instantaneous power consumption
@20dBm
receive current 7.3 mA
sleep current 0.6 μA software shutdown
Operating temperature -40 20 85
Working humidity 10 60 90 %
Storage -40 20 125
RF
parameters
parameter value Remark
Working frequency 2400~2480 MHz Support ISM band
transmit power 19.5 dBm Software adjustable
blocking power 0 ~ 10.0 dBm The probability of burning at close range is small
Receive sensitivity -106 dBm The air rate is 250kbps
Modulation GFSK
matched impedance 50 Equivalent impedance of PCB
on-board antenna
Measured distance 700 m Clear and open, 2.5 meters high, air speed 250kBps
Pin Definition
E72-2G4M20S1E/Link72
pin number
pin name
Pin Orientation
pin usage
1
GND
Ground wire, connected to the power reference ground
2
DIO_7
output
STATUS_LED, status indicator, active low. The long light is on standby
state, fast blinking means creating a new network or joining a network, 1S periodic blinking means allowing network access;
3
DIO_8
NC pin, floating;
4
DIO_9
NC pin, floating;
5
DIO_10
NC pin, floating;
6
DIO_11
NC pin, floating;
7
DIO_12
input
UART_RX , serial port input signal pin;
8
DIO_13
output
UART_TX , serial port output signal pin;
9
DIO_14
dangling;
10
DIO_15
input
BOOT_LOADER , active low;
11、12
GND
Ground wire, connected to the power reference ground;
13
JTAG_TMSC
input /
output
JTAG_TMSC , if not used, please leave it empty;
14
JTAG_TCKC
input /
output
JTAG_TMSC , if not used, please leave it empty;
15
DIO_16
input /
output
JTAG_TDO , if not used, please leave it empty;
16
DIO_17
input /
output
JTAG_TDI , if not used, please leave it empty;
17
DIO_18
NC pin, floating;
18
DIO_19
NC pin, floating;
19
GND
Ground wire, connected to the power reference ground
20
VCC
The module power supply is positive reference power, the voltage range is 1.9 ~ 3.8V ;
21
DIO_20
NC pin, floating;
22
DIO_21
NC pin, floating;
23
GND
Ground wire, connected to the power reference ground;
24
RESET_N
enter
Reset pin, active low;
25
DIO_22
NC pin, floating;
26
DIO_23
NC pin, floating;
27
DIO_24
NC pin, floating;
28
DIO_25
NC pin, floating;
39
DIO_26
NC pin, floating;
30
DIO_27
NC pin, floating;
31
DIO_28
NC pin, floating;
32
DIO_29
NC pin, floating;
33
DIO_30
NC pin, floating;
34
GND
Ground wire, connected to the power reference ground;
File Downloads

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Back to Top
Product has been added to your cart