Home
Shop
Wishlist0
(1)

L293 Motor Driver Shield

L293 Motor Driver Shield for DC motor/ stepper motor / servo motor

115.00 EGP

Purchase this product now and earn 12 Points!
Buy Now
Availability: In Stock
SKU:300000009170
Key Features OF L293D Motor Shield:
  • Drive 4 DC motors with speed and direction control
  • Driver: 2 x L293D
  • The shift register 74HC595
  • The reset button
  • Drive 2 stepper motors
  • Drive 2 servo motors
  • 4.5 – 25V motor voltage range
  • 1.2A peak current per channel (600mA continuous)

The L293D Motor Shield can drive up to 4 DC motors at voltages from 4.5 – 25V and at currents of up to 1.2A peak (600mA continuous) per motor with speed and direction control.

The module can also support up to 2 stepper motors.  Each stepper motor takes the place of 2 of the DC motors, so you can run 2 stepper motors or 1 stepper motor and 2 DC motors or 4 DC motors.

The shield also technically supports 2 servo motors for which there are two 3-pin headers on the module.  Unfortunately, it powers the servo motors directly off the Arduino 5V which is usually not a great idea.  Doing so can overheat the Arduino on-board 5V regulator as well as induce electrical noise into the Arduino 5V power causing intermittent problems that are difficult to troubleshoot.  On the plus side, it does have a 100uF capacitor on these power pins which does help somewhat.  If using this feature, use only with small servos like the SG90, and keep an eye out for any issues.  As another option, the traces to the 5V center pins on the servo headers can be easily cut and rewired to a separate 5V power source or the motor source if powered off of 5-6V.

Motor Power Connections

Motor voltage must be between 4.5 – 25V.  This power can be shared with the Arduino or be separate.  To select this, there is a jumper near the 2 terminal power connector labeled PWR.

When this jumper is installed, the power from the Arduino DC power jack is also connected to the motors.  Vin (marked 9V on the board) is brought up form the Arduino to power the motors.

When the jumper is removed, that isolates the motor power from the Arduino and it must be supplied separately by connecting power to the 2 terminal power connector.  Note:  Do not apply power to the 2 terminal power connector with the jumper in place or it will short the two power supplies together! 

     1 x 2 Terminal EXT_PWR (Motor Power)

  • +M = Motor Vcc which must be between 4.5 and 25V.
  • GND = Motor Ground.
DC Motor Connections

The motor connections are via two screw terminals for each motor and are labeled M1 thru M4.  The center terminal on the 5-pos terminal blocks are connected to ground.

The wiring of which lead of the motor connects to which terminal is somewhat arbitrary and relative to what you consider forward vs reverse motor operation.  If the motor goes in the opposite direction that you expect, simply reverse the wiring.

     1 x 2 Terminal M1 – M4 (DC Motor 1-4)

  •  Motor ‘-‘ positive lead
  •  Motor ‘+’ negative lead
 Stepper Motor Connections

Stepper motors are typically 4 wires.  Coil 1 will connect across one motor port such as M1 (M3) and coil 2 will connect across the other motor port such as M2 (M4).  If the stepper motor has 5 wires, the center tap wire will be connected to the center ground terminal.

 1 x 2 Terminal M1(M3) – M2(M4)  (Servo Motor 1-2)

  •  Motor Coil 1
  •  Motor Coil 2
Arduino to Shield Pin Connections

The shield has a remote reset button located on it for easy access.

The shield uses Pins D3,D4, D5, D6, D7, D8, D11 and D12 for DC and stepper motor control.

D9 and D10 come out to the Servo headers.  D10 is connected to Servo 1.  D9 is connected to Servo 2,

The other pins are available including the 6 analog pins that can also be used as digital I/O.  These have solder pads so that a header can be added if desired for easy connections.  Next to that is a row of 5V and Ground connections that can also be populated with headers and can be handy for hooking up various sensors.

1 review for L293 Motor Driver Shield

  1. احمد علي المالحي

    هوا ممكن يشغل كام استبر مع بعض لو سمحت ؟؟

Only logged in customers who have purchased this product may leave a review.

Back to Top
Product has been added to your cart