Home
Shop
Wishlist0

RFID module 13.56 MHz Card Reader MFRC522 Reader/Writer

RFID module- RC522 Kits S50 13.56 Mhz ,With Tags SPI Write & Read for arduino

150.00 EGP

Purchase this product now and earn 15 Points!
Buy Now
Availability: In Stock
SKU:6075602286835

Short Description

MFRC522 RFID Module Read/Write (13.56MHz)

  • 13.56MHz RFID module
  • Operating voltage: 2.5V to 3.3V
  • Communication : SPI, I2C protocol, UART
  • Maximum Data Rate: 10Mbps
  • Read Range: 5cm
  • Current Consumption: 13-26mA
  • Power down mode consumption: 10uA (min)
  • Module Size: 60mm x 40mm
  • Card Size: 85mm x 53mm
  • Key Length: 39mm

This module is used to communicate between your Arduino or favorite MCU with RFID technology. It uses NFC (Near Field Communication), a type of wireless communication used in many applications, even in some new phones.

The kit comes with two different types of passive tags: 1x round tag, 1x card type tag. The tags are passive, which means that don’t need a battery to run, they use the energy from the reader to send the information to it.

The antenna on the reader allows to communicate with the tags to a maximum distance of 40-60mm. The reader communicates with the MCU or Arduino through SPI communication

It can be used for applications such as for personal door access, etc.

MF RC522 using advanced modulation and demodulation concept completely integrated in all types of 13.56MHz passive contactless communication methods and protocols. Support 14443A compatible transponder signals. The digital part handles ISO14443A framing and error detection. In addition, support fast CRYPTO1 encryption algorithms, terminology validation MIFARE products. MFRC522 supports MIFARE Series higher speed non-contact communication, two-way data transfer rates up to 424kbit / s. As a highly integrated 13.56MHz card reader new family of chips, MF RC522 MF RC500 and MF RC530 and there are many similarities, but also have many features and differences. It is between the host communication using SPI mode, helps to reduce connection, reduce PCB board size and cost.

MF522-AN module adopts Philips MFRC522 original reader circuit chip design, easy to use, low cost, suitable for equipment development, development of advanced applications such reader users, the need for RF card terminal design / production of the user. This module can be loaded directly into a variety of readers molds. Module uses voltage of 3.3V, through the SPI interface simple few lines can be directly connected to the user any CPU board communication module can guarantee stable and reliable work.

Pin Configuration:

Pin Number Pin Name Description
1 Vcc Used to Power the module, typically 3.3V is used
2 RST Reset pin ? used to reset or power down the module
3 Ground Connected to Ground of system
4 IRQ Interrupt pin ? used to wake up the module when a device comes into range
5 MISO/SCL/Tx MISO pin when used for SPI communication, acts as SCL for I2c and Tx for UART.
6 MOSI Master out slave in pin for SPI communication
7 SCK Serial Clock pin ? used to provide clock source
8 SS/SDA/Rx Acts as Serial input (SS) for SPI communication, SDA for IIC and Rx during UART

Features:

RFID Reader:

  • Input voltage: 3.3v
  • Chip: MFRC-522 RC522
  • Operation Current : 13~26mA
  • Idle Current :10~13mA
  • Sleep Current : <80μA
  • Peak Current : <30mA
  • Operation Frequency :13.56MHz
  • Read Range 0~60mm (mifare1)
  • Interface SPI Data Transition Rate : Up to 10Mbit/s
  • Supported card types : mifare1 S50, mifare1 S70, mifare UltraLight, mifare Pro, mifare Desfire
  • Operation Temperature : -20-80° Celsius
  • Storage temperature : -40-85° Celsius
  • Relative Humidity : %5~%95

   IC Card:

  • Capacity: 8KB EEPROM
  • Divided into 16 sectors, each sector is 4 blocks, each block is 16 bytes, each block as 1 unit
  • Each sector has a separate set of passwords and access control
  • Each card has a unique 32-bit serial number
  • Have anti-collision mechanism, support for multi-card operations
  • No power, with an antenna, embedded encryption control logic and communication logic circuit
  • Data retention period of 10 years, can be rewritten 100,000 times, reading limitless
  • Operating Temperature -20° C ~ 50° C Humidity is 90%
  • Operating frequency is 13.56MHz
  • RF protocol : ISO14443A
  • Communication speed : 106KBPS
  • Read and write distance : ≤ 10cm (regardless of reader)

NFC TAG Keychain:

  • Main Chip: Philips Mifare 1 S50;
  • Storage capacity: 8Kbit, 16 partitions, each partition with 2 group passwords;
  • Operating Frequency: 13.56 MHz;
  • Communication speed: 106K Baud Rate
  • Read and write distance: 2.5 ~ 10cm
  • Read and write time: 1 ~ 2ms
  • Operating Temperature: -20° C to 85° C
  • Endurance:> 100,000 times;
Package includes:
  • 1 x MFRC522 RFID Module
  • 1 x the standard S50 blank card
  • 1 x S50 special-shaped card a (as shown by the key ring shape)
  • 2 x straight, curved rows of pin of the article

Useful links

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Back to Top
Product has been added to your cart