Product Description
The ZCU102 Evaluation Kit enables designers to jumpstart designs for automotive, industrial, video, and communications applications. This kit features a Zynq™ UltraScale+™ MPSoC with a quad-core Arm® Cortex®-A53, dual-core Cortex-R5F real-time processors, and a Mali™-400 MP2 graphics processing unit based on 16nm FinFET+ programmable logic fabric by AMD. The ZCU102 supports all major peripherals and interfaces, enabling development for a wide range of applications.
Key Features & Benefits
- Optimized for quick application prototyping with Zynq UltraScale+ MPSoC
- DDR4 SODIMM – 4GB 64-bit w/ ECC attached to processing system (PS)
- DDR4 Component – 512MB 16-bit attached to programmable logic (PL)
- PCIe® Root Port Gen2 x4, USB3, Display Port, and SATA
- 4x SFP+ interfaces for Ethernet
- 2x FPGA Mezzanine Card (FMC) interfaces for I/O expansion, including 16 16.3Gb/s GTH transceivers and 64 user-defined differential I/O signals
Featured AMD Devices
Featuring the Zynq UltraScale+ XCZU9EG-2FFVB1156 MPSoC
| System Logic Cells (K) | 600 |
|---|---|
| Memory (Mb) | 32.1 |
| DSP Slices | 2,520 |
| Maximum I/0 Pins | 328 |
PRODUCT INFORMATION
Specifications
Board Features
Featuring the ZCU102 Evaluation Board
Configuration
- Onboard JTAG configuration circuitry to enable configuration over USB
- Dual Quad-SPI flash memory
- Boot from SD card
Memory
- PS 4GB DDR4 64-bit SODIMM w/ ECC
- PL 512MB DDR4 component memory ([256 Mb x 16] devices) at 1200MHz / 2400Mbps DDR
- 8KB IIC EEPROM
- Dual 64MB Quad SPI flash
- SD card slot
Control & I/O
- 6x Directional Push Buttons (5x PL, 1x PS)
- DIP switches (8x PL)
- PMBUS & System Controller MSP430 for power, clocks, and I2C bus switching
- USB2/3 (MIO ULPI and 1 GTR)**
Expansion Connectors
- 2x FMC-HPC connectors (16 GTH Transceivers, 64 differential user defined signals)
- 2x PMOD headers
- IIC
Communication & Networking
- RGMII communications at 10, 100, or 1000 Mb/s. Serial GMII interface-supports a 1 Gb/s SGMII interface
- 4x SFP+ cage
- SMA GTH support (4x SMA Tx/Rx connectors)
- UART To USB bridge
- RJ45 Ethernet connector
- SATA (1 x GTR)**
- PCIe Gen2x4 Root Port**
Display
- HDMI video input and output (3 GTH)
- External Retimer device driving an HDMI output connector
- 9x GPIO user LEDs (8x PL, 1x PS)
- VESA DisplayPort 1.2 source-only controller supports up to two lanes of main link data at rates of 1.62 Gb/s, 2.70 Gb/s, or 5.40 Gb/s.
Clocking
- Programmable clocks
- System clocks, user clocks, jitter attenuated clocks
- 2x SMA MGT input clocks
Power
- 12V wall adapter or ATX
** Switch enables either PCIe Root Port OR SATA, USB2/3 & DisplayPort
What’s Inside
- ZCU102 Evaluation Board
- Access to a full seat of Vivado™ Design Suite: Design Edition
- Ethernet Cable
- Targus USB-3
- USB3 Adapter
- USB Micro Cable
- Power Cords and Adapter
- Access to SDSoC Environment
Reviews
There are no reviews yet.