Buck Converter vs LDO Regulator: How to Choose the Right One?

Buck Converter vs LDO Regulator: How to Choose the Right One? Compare efficiency, heat, noise, and performance to select the best regulator for your project.

Buck Converter vs LDO Regulator
On this page
  1. 1. Introduction
  2. 2. What Is a Voltage Regulator?
  3. 3. What Is a Buck Converter?
  4. 4. What Is an LDO Regulator?
  5. 5. How Does a Buck Converter Differ from an LDO Regulator?
  6. 6. Understanding Power, Efficiency, and Heat
  7. 7. Output Noise and Voltage Stability
  8. 8. Input Voltage, Output Current, and Dropout Voltage
  9. 9. Advantages and Limitations of Each Regulator
  10. 10. When Should You Choose a Buck Converter?
  11. 11. When Should You Choose an LDO Regulator?
  12. 12. Can You Use a Buck Converter and an LDO Together?
  13. 13. Practical Examples and Calculations
  14. 14. How to Choose the Right Regulator for Your Project?
  15. 15. Common Mistakes to Avoid
  16. 16. Frequently Asked Questions
  17. 17. Conclusion
  18. محوّل Buck أم منظّم الجهد LDO: كيف تختار الأنسب لمشروعك؟
  19. 1. مقدمة
  20. 2. ما منظّم الجهد؟
  21. 3. ما محوّل Buck؟
  22. 4. ما منظّم الجهد LDO؟
  23. 5. ما الفرق بين محوّل Buck ومنظّم الجهد LDO؟
  24. 6. فهم القدرة والكفاءة وتوليد الحرارة
  25. 7. ضوضاء الخرج واستقرار الجهد
  26. 8. جهد الدخل وتيار الخرج وجهد السقوط
  27. 9. مزايا وعيوب كل نوع من منظمات الجهد
  28. 10. متى تختار محول Buck؟
  29. 11. متى تختار منظم LDO؟
  30. 12. هل يمكن استخدام محول Buck ومنظم LDO معًا؟
  31. 13. أمثلة عملية وحسابات تطبيقية
  32. 14. كيف تختار منظم الجهد المناسب لمشروعك؟
  33. 15. أخطاء شائعة ينبغي تجنبها
  34. 16. الأسئلة الشائعة
  35. 17. الخلاصة

1. Introduction

Choosing the right voltage regulator is an important step in designing an electronic circuit. Microcontrollers, sensors, communication modules, and other electronic components often require a stable DC supply voltage, such as 5V, 3.3V, or 1.8V, even when the available power source provides a different voltage.

Two common solutions are the Buck Converter and the LDO (Low-Dropout) Regulator. Both can reduce a higher DC voltage to a lower, regulated voltage, but they use different operating principles and have different advantages.

A buck converter uses high-speed switching and energy-storage components to convert voltage efficiently. An LDO is a type of linear regulator that adjusts its internal pass element to maintain the desired output voltage, even when the input voltage is relatively close to the output voltage.

Neither option is always better. A buck converter is often preferred when efficiency and heat reduction are important, particularly at higher currents or with large voltage differences. An LDO is often suitable for low-current circuits, simple designs, and applications where low output noise is important.

This article explains how both regulators work, compares their efficiency, heat generation, noise, and limitations, and provides practical calculations to help beginners, hobbyists, and engineers choose the right solution for their projects.

2. What Is a Voltage Regulator?

A voltage regulator is an electronic circuit or device that maintains a relatively stable output voltage despite changes in input voltage or load current, provided it operates within its specified limits.

For example, a microcontroller may require a 3.3V supply, while the available power source provides 12V. A suitable regulator can convert the 12V input into a stable 3.3V output.

Voltage regulators are commonly divided into two main categories:

  • Linear regulators: Regulate voltage by controlling a pass transistor. LDO regulators belong to this category.
  • Switching regulators: Use switching transistors and energy-storage components to convert electrical power efficiently. Buck converters are one type of switching regulator.

The choice depends on the input voltage, required output voltage, load current, allowable heat, noise requirements, and available space.

3. What Is a Buck Converter?

A buck converter is a switching DC-DC converter designed to reduce a higher DC input voltage to a lower DC output voltage.

For example, a buck converter can convert 12V to 5V or 5V to 3.3V while maintaining good efficiency when properly designed.

How Does a Buck Converter Work?

A typical buck converter contains a switching transistor, an inductor, capacitors, and either a diode or a synchronous switching transistor.

Its operation involves two main phases:

  1. Switch ON: The switching transistor conducts, allowing energy from the input supply to flow through the inductor to the load. The inductor stores energy in its magnetic field.
  2. Switch OFF: The transistor stops conducting, but the inductor continues supplying current through the freewheeling diode or synchronous transistor.

This process repeats rapidly. The inductor and capacitors smooth the resulting electrical waveform, while a feedback control circuit adjusts the switching operation to maintain the required output voltage.

Understanding the Duty Cycle

The duty cycle (D) is the fraction of each switching period during which the main switching transistor is ON.

For an ideal buck converter operating in continuous conduction mode:

Vout = Vin × D

Where:

  • Vout is the output voltage.
  • Vin is the input voltage.
  • D is the duty cycle, expressed as a fraction between 0 and 1.

For example, if the input voltage is 12V and the duty cycle is 0.5:

Vout = 12 × 0.5 = 6V

This is an idealized calculation. Actual output voltage depends on the converter’s feedback controller, component losses, operating mode, and other design factors.

Common Buck Converter Modules

Several buck converter ICs and modules are popular in electronics projects:

  • LM2596: A step-down switching regulator commonly found in adjustable converter modules.
  • XL4015: A switching regulator used in many higher-current step-down modules, subject to the module’s thermal and electrical limits.
  • MP1584: A compact buck converter IC commonly used in small DC-DC modules.

When selecting a module, check its input-voltage range, output-current rating, efficiency, thermal performance, and required cooling. A module’s advertised maximum current may not be sustainable without adequate heat dissipation.

4. What Is an LDO Regulator?

An LDO (Low-Dropout Regulator) is a type of linear voltage regulator that can maintain its regulated output with a relatively small difference between its input and output voltages.

For example, an appropriate LDO may convert 3.6V to 3.3V to power a sensor, microcontroller, or analog circuit.

How Does an LDO Work?

An LDO typically contains a voltage reference, an error amplifier, a feedback network, and a pass transistor.

The feedback circuit continuously monitors the output voltage and compares it with an internal reference. The error amplifier adjusts the pass transistor to correct deviations and maintain the desired output voltage.

Unlike a buck converter, an LDO does not use a high-frequency switching process to transfer energy. Instead, the pass transistor operates in its linear region and dissipates the excess voltage as heat.

An LDO can regulate correctly only when its input voltage remains high enough above the output voltage to satisfy its dropout-voltage requirement.

Understanding Dropout Voltage

Dropout voltage is the minimum input-to-output voltage difference required for an LDO to maintain its specified regulation under particular operating conditions.

For example, if an LDO requires a dropout voltage of 200mV and the desired output is 3.3V, the input must generally remain at or above:

  • Vin ≥ Vout + Vdropout
  • Vin ≥ 3.3 + 0.2 = 3.5V

The actual dropout voltage depends on the regulator model, load current, and temperature. Always check the manufacturer’s datasheet rather than assuming every LDO has the same dropout voltage

Common LDO Regulator Models

Examples of LDO regulators used in electronic circuits include:

  • AMS1117: A family of linear regulators available in several output-voltage versions, commonly used on development boards and regulator modules.
  • MCP1700: A low-quiescent-current LDO suitable for many low-power applications.
  • AP2112K: A compact LDO used in various 3.3V and 5V power-supply applications.

These devices differ in maximum input voltage, output current, dropout voltage, quiescent current, thermal limits, and capacitor requirements. Choose a specific model according to the circuit’s needs.

5. How Does a Buck Converter Differ from an LDO Regulator?

Although both devices can provide a lower regulated DC voltage, their internal operation affects efficiency, heat generation, noise, and circuit complexity.

Parameter Buck Converter LDO Regulator
Regulation method High-frequency switching Linear pass transistor
Voltage reduction Yes Yes
Typical efficiency Often high, depending on operating conditions Strongly affected by the input/output voltage ratio
Heat generation Generally lower for substantial voltage drops Can be high with large voltage drops or high current
Output ripple Switching ripple may be present Generally no switching ripple generated internally
Electromagnetic interference Requires attention to switching layout and filtering Usually less switching-related EMI
Circuit complexity Higher Usually lower
External components Typically an inductor, capacitors, and switching components Typically input/output capacitors
Light-load behavior Depends on the converter’s operating mode and quiescent losses Can be excellent with a low-quiescent-current model
Best suited for Efficient power conversion, particularly at higher loads Simple regulation, low-noise rails, and small voltage differences

A buck converter is often the better choice when substantial power must be delivered efficiently. An LDO may be more suitable when the voltage difference is small, the current is low, or noise requirements dominate. Neither device is automatically superior in every application.

6. Understanding Power, Efficiency, and Heat

Power efficiency and heat generation are among the most important factors when choosing a voltage regulator.

Output Power

Output power is calculated from output voltage and output current:

Pout = Vout × Iout

For example, a 5V output at 2A requires:

Pout = 5 × 2 = 10W

This means the load receives 10W of electrical power.

Power Dissipation in an LDO

For a linear regulator, approximate power dissipation is:

Ploss = (Vin − Vout) × Iout

For example, reducing 12V to 5V at 0.5A gives an approximate regulator loss of:

Ploss= (12 − 5) × 0.5 = 3.5W

The regulator must dissipate approximately 3.5W as heat under these assumptions. That is a substantial thermal load for a small component and may require a different regulator, improved thermal design, or both.

This simplified calculation assumes that the input current is approximately equal to the output current and neglects the regulator’s ground current. For greater accuracy, use the actual input and output currents.

Efficiency of a Buck Converter

The efficiency of a regulator is the ratio of output power to input power, expressed as a percentage:

η = (Pout ÷ Pin) × 100%

Assume a buck converter provides 5V at 0.5A with an efficiency of 85%.

First, calculate the output power:

Pout = 5 × 0.5 = 2.5W

Then calculate the approximate input power:

Pin = Pout ÷ η

Using 0.85 for 85% efficiency:

Pin = 2.5 ÷ 0.85 = 2.94W

At an input voltage of 3.7V, the approximate input current is:

Iin = Pin ÷ Vin

Iin = 2.94 ÷ 3.7 = 0.79A

The converter’s approximate power loss is:

Ploss = Pin − Pout

Ploss = 2.94 − 2.5 = 0.44W

The converter therefore dissipates approximately 0.44W under these assumed conditions.

Comparing Heat Generation

Consider a 12V input, 5V output, and 1A load.

For an LDO:

Ploss = (12 − 5) × 1 = 7W

For a buck converter operating at an assumed efficiency of 90%:

Pin= 5 ÷ 0.90 = 5.56W

Ploss = 5.56 − 5 = 0.56W

In this example, the LDO dissipates approximately 7W, while the buck converter dissipates approximately 0.56W. This illustrates why a buck converter is usually preferable for large voltage drops and substantial current.

These figures are illustrative calculations, not guaranteed performance values for every device. Real efficiency depends on the selected regulator, input and output voltages, load, temperature, and circuit design.

7. Output Noise and Voltage Stability

Output noise is another important factor, especially in circuits containing analog sensors, audio circuits, ADCs, DACs, and radio-frequency components.

Buck Converter Noise

A buck converter rapidly switches its power transistor between ON and OFF states. This switching action creates output ripple and can generate electromagnetic interference (EMI).

Noise can be reduced by using appropriate capacitors, a suitable PCB layout, short high-current paths, and carefully designed filtering.

However, switching ripple is not necessarily a problem for every application. Many digital circuits can operate correctly with a properly designed buck converter.

LDO Noise

An LDO does not generate the periodic switching ripple associated with a switching converter. Many LDOs are therefore useful for noise-sensitive circuits.

However, an LDO is not completely noise-free. Its internal circuitry generates noise, and its ability to reject noise from the input supply depends on its power-supply rejection ratio (PSRR), operating frequency, load, and other conditions.

A low-noise LDO can be particularly useful for powering sensitive analog components, provided its voltage, current, and thermal requirements are satisfied.

Which Is Better for Sensitive Electronics?

Choose based on the actual noise requirements of the circuit:

  • For a digital microcontroller, a suitable buck converter may be sufficient.
  • For a sensitive analog sensor or RF circuit, a low-noise LDO may be preferable.
  • For a design requiring both high efficiency and low noise, a buck converter followed by an LDO may be appropriate.

Always check the LDO’s noise and PSRR specifications at the relevant frequencies rather than assuming that every LDO will remove all switching noise.

8. Input Voltage, Output Current, and Dropout Voltage

Before selecting a regulator, confirm that its electrical limits match the intended application.

Input and Output Voltage
  • The input voltage must fall within the regulator’s specified operating range.
  • A buck converter can step down voltage, but it cannot normally produce a regulated output above its input voltage. If the output must exceed the input, consider a boost converter instead.
  • An LDO requires its input voltage to exceed the desired output voltage by at least the dropout voltage under the relevant operating conditions.
  • For example, converting 3.5V to 3.3V with an LDO requiring 200mV of dropout leaves little margin. Input-voltage variations or a higher load current may cause the output to fall out of regulation.
Maximum Output Current
  • The regulator must supply the load’s maximum current, including brief peaks caused by devices such as wireless modules, motors, and other dynamic loads.
  • Do not rely only on the headline current rating. Check thermal performance, current limiting, PCB copper area, package limitations, and the manufacturer’s recommended operating conditions.
Quiescent Current and Battery Life

Quiescent current (IQ) is the current consumed internally by a regulator to operate its control circuitry. It matters in battery-powered designs, particularly when the load spends long periods in sleep mode.

A buck converter can be highly efficient at substantial loads, but some models consume significant current or lose efficiency at very light loads. A low-quiescent-current LDO may be a better choice for a low-power device that spends most of its time sleeping.

Compare actual efficiency curves and quiescent-current specifications over the expected operating range.

9. Advantages and Limitations of Each Regulator

Buck Converter Advantages
  • High efficiency in many step-down applications.
  • Lower power dissipation for substantial voltage differences and loads.
  • Suitable for powering microcontrollers, development boards, displays, and other current-demanding circuits.
  • Can extend battery runtime when selected and designed appropriately.
  • Supports a wide range of power levels, depending on the device and circuit design.
Buck Converter Limitations
  • Requires more components and careful circuit design.
  • Switching ripple and EMI may affect sensitive circuits.
  • PCB layout and component selection can strongly influence performance.
  • Efficiency varies with input voltage, output current, switching frequency, and operating mode.
  • Inductors and other components can increase circuit size.
LDO Advantages
  • Simple circuit implementation.
  • Usually requires fewer external components.
  • Often produces low output ripple without switching-related noise.
  • Can provide good regulation for low-power circuits.
  • May perform well at very light loads when a low-quiescent-current model is selected.
  • Can regulate when the input voltage is close to the output, provided the dropout requirement is met.
LDO Limitations
  • Can generate substantial heat when the input-to-output voltage difference is large.
  • Efficiency is limited by the voltage ratio and the regulator’s internal current consumption.
  • Requires sufficient input-to-output voltage headroom.
  • Maximum output current may be constrained by thermal limits.
  • Output capacitor requirements and stability conditions vary between models.

10. When Should You Choose a Buck Converter?

A buck converter is generally a strong choice when the application requires efficient voltage reduction.

 

Consider a buck converter when:

  • Reducing 12V to 5V or 5V to 3.3V at a moderate or high current.
  • Powering Arduino, ESP8266, ESP32, or Raspberry Pi-based systems from a suitable higher-voltage source.
  • Operating battery-powered equipment where energy efficiency is important.
  • Supplying displays, communication modules, or other loads with significant current demand.
  • Reducing heat in a compact enclosure.

For example, a 12V supply powering a 5V, 1A load provides a clear reason to consider a buck converter: an LDO would dissipate approximately 7W under the simplified assumptions discussed earlier.

Before using a buck converter, check the input-voltage range, output-current capability, efficiency, output ripple, switching frequency, and thermal performance.

11. When Should You Choose an LDO Regulator?

An LDO is often appropriate when simplicity, low noise, or a small input-to-output voltage difference is more important than achieving the highest possible efficiency.

Consider an LDO when:

  • Reducing 3.6V to 3.3V for a low-current circuit.
  • Powering sensitive analog sensors or reference circuits.
  • Providing a clean supply rail for an ADC, DAC, or RF component.
  • Building a simple, low-power circuit with limited space for external components.
  • Supplying a battery-powered device whose load current is small and whose sleep current is important.

For example, converting 3.6V to 3.3V at 100mA gives an approximate LDO power loss of:

Ploss = (3.6 − 3.3) × 0.1 = 0.03W

The regulator dissipates approximately 30mW, which is a relatively small thermal load.

However, verify the LDO’s dropout voltage, quiescent current, maximum input voltage, output-current rating, and capacitor requirements before choosing it.

12. Can You Use a Buck Converter and an LDO Together?

Yes. Using both devices in sequence is a common power-supply design technique called post-regulation.

In this arrangement, the buck converter performs the main voltage reduction efficiently, and the LDO provides additional regulation and may reduce noise reaching a sensitive load.

A typical arrangement is:   12V input → Buck Converter → 3.6V intermediate supply → LDO → 3.3V output

The buck converter reduces the large voltage difference, while the LDO regulates the final output voltage.

Benefits of Using Both
  • Better overall efficiency than using an LDO alone for a large voltage reduction, in many applications.
  • Potentially lower output noise and ripple.
  • Improved supply quality for sensitive analog and RF circuits.
  • Flexibility in designing separate power rails for digital and analog components.
Important Design Considerations

The LDO must have sufficient input voltage to maintain regulation, and its power dissipation must remain within safe limits.

For example, if the LDO converts 3.6V to 3.3V at 100mA:

Ploss = (3.6 − 3.3) × 0.1 = 0.03W

That is a small loss, while the buck converter handles the main voltage reduction.

The LDO’s PSRR must also be checked at the buck converter’s switching frequency. An LDO does not automatically eliminate all switching noise, especially at high frequencies.

13. Practical Examples and Calculations

The following examples show how to apply the selection principles to common electronics projects.

Example 1: Powering an ESP32 from a 12V Supply

Suppose a 12V supply must provide a regulated 3.3V rail for an ESP32 circuit drawing 500mA.

The output power is:

  • Pout = Vout × Iout
  • Pout = 3.3 × 0.5 = 1.65W

If an LDO were used, its approximate power dissipation would be:

  • P =(12 − 3.3) × 0.5 = 4.35W

This is a substantial amount of heat. A suitable buck converter would generally be the better choice for this voltage difference and load current.

In practice, select a converter that can handle the supply’s maximum voltage, the ESP32’s peak current, and any additional loads. Do not connect 12V directly to a 3.3V power pin.

Example 2: Powering a 3.3V Sensor from a 3.6V Supply

Suppose a sensor requires 3.3V at 50mA, and the available supply is 3.6V.

The approximate LDO power dissipation is:

  • Ploss = (3.6 − 3.3) × 0.05 = 0.015W

The result is only 15mW, so heat generation is low under these conditions.

An LDO may be a practical choice because the voltage difference and current are small. However, its dropout voltage must be low enough to maintain regulation across the full input-voltage range.

Example 3: Powering a Sensitive Analog Circuit
  • Suppose an analog sensor requires a stable 3.3V supply, and its measurements are sensitive to power-supply noise.
  • One option is to use a low-noise LDO if the available input voltage is sufficiently close to 3.3V and the load current is within its limits.
  • Another option is to use a buck converter to reduce the main supply voltage, followed by an LDO to provide additional filtering and regulation.
  • The best choice depends on the sensor’s noise sensitivity, the LDO’s PSRR at the relevant frequencies, the required current, and the total power budget.

14. How to Choose the Right Regulator for Your Project?

Use the following checklist when selecting a regulator for a new design.

  1. Determine the input-voltage range. Include minimum and maximum supply voltage, battery discharge, and possible voltage transients.
  2. Identify the required output voltage. Confirm the voltage tolerance specified by the powered components.
  3. Calculate the maximum load current. Include startup current and short-duration peaks.
  4. Estimate power loss and heat. For an LDO, use the voltage difference and load current. For a buck converter, estimate loss using its efficiency.
  5. Evaluate noise requirements. Consider switching ripple, EMI, LDO noise, and PSRR.
  6. Check battery performance. Compare quiescent current and efficiency at both normal load and standby conditions.
  7. Verify thermal and electrical ratings. Review the manufacturer’s datasheet, package limitations, and recommended operating conditions.
  8. Consider circuit complexity and cost. Account for external components, PCB layout, and filtering requirements.
Quick Selection Guide
Application Recommended starting point
12V to 5V at 1A Buck converter
5V to 3.3V at high current Usually buck converter
3.6V to 3.3V at low current LDO, if dropout allows
Low-noise analog supply Low-noise LDO or buck plus LDO
Battery-powered, very low standby current Compare low-IQ buck and LDO specifications
Large voltage reduction with limited cooling Usually buck converter

These are starting points rather than absolute rules. The final decision depends on the particular regulator, operating conditions, and application requirements.

15. Common Mistakes to Avoid

Choosing Based Only on Maximum Current

A regulator advertised as supporting 1A may not deliver 1A continuously in every circuit. Thermal limits, PCB layout, package size, and ambient temperature can reduce the usable current.

Assuming Every LDO Is Low Noise

LDOs differ in internally generated noise and their ability to reject input ripple. Check the actual datasheet specifications, including the measurement bandwidth and PSRR frequency range.

Ignoring Dropout Voltage

An LDO may fail to maintain the required output voltage when its input approaches the output voltage. Check the dropout specification at the intended current and temperature.

Assuming a Buck Converter Is Always More Efficient

Buck converters have switching losses and internal operating current. At very light loads or when the input voltage is only slightly above the output voltage, an LDO may be more efficient.

Ignoring Heat Dissipation

Calculate the expected power loss and verify that the device can dissipate the resulting heat safely. Do not assume that a small regulator can handle several watts without appropriate thermal design.

Forgetting Capacitor and Layout Requirements

Follow the manufacturer’s recommendations for input and output capacitors. For buck converters, pay particular attention to the switching-current paths, grounding, and PCB layout. For LDOs, verify output-capacitor requirements and stability conditions.

16. Frequently Asked Questions

Is a buck converter better than an LDO?

Not in every situation. A buck converter is generally better for efficient step-down conversion when the voltage difference or load current is significant. An LDO can be preferable for low-noise, low-current circuits and small voltage differences.

Can an LDO convert 12V to 5V?

Yes, if the selected LDO supports the input voltage and load current. However, at 1A, the approximate power dissipation would be:

Ploss = (12 − 5) × 1 = 7W

This can cause excessive heating in a small package. A buck converter is usually more suitable for this application.

Does a buck converter produce a stable output voltage?

Yes. A properly designed buck converter uses a control circuit to regulate its output despite changes in input voltage and load current, within its specified operating range. Its output still contains some ripple, and the amount depends on the design.

Why are LDOs used after buck converters?

An LDO can provide additional regulation and reduce some of the ripple and noise from the preceding switching converter. This can be useful for sensitive analog and RF circuits, provided the LDO has enough input-voltage headroom.

Which regulator is better for battery-powered projects?

It depends on the battery voltage range, load current, and standby requirements. A buck converter may provide better efficiency at substantial loads, while a low-quiescent-current LDO may be attractive for low-current applications or when the input voltage is close to the output voltage.

Can I use a buck converter to increase voltage?

A standard buck converter is designed to reduce voltage. If the output voltage must exceed the input voltage, use a boost converter or an appropriate buck-boost converter.

How do I calculate the power lost in a regulator?

For an LDO, a useful approximation is:

Ploss = (Vin− Vout) × Iout

For a switching converter, when efficiency is known:

Ploss= Pout × (1 ÷ η − 1)

Here, η is efficiency expressed as a fraction. For example, 90% efficiency is represented as 0.90.

What specifications should I check before buying a regulator?

Check the input-voltage range, output voltage, maximum output current, efficiency, dropout voltage where applicable, thermal performance, quiescent current, output noise, capacitor requirements, and protection features.

17. Conclusion

Choosing between a buck converter and an LDO regulator requires balancing efficiency, heat generation, output noise, circuit complexity, and load requirements.

A buck converter is usually the better starting point for applications involving large voltage reductions, substantial current, or strict power-efficiency requirements. An LDO regulator is often a good choice for low-current circuits, small voltage differences, and noise-sensitive applications.

For designs requiring both efficient power conversion and a clean supply rail, combining a buck converter with a suitable LDO can provide a useful compromise.

The most reliable approach is to calculate the expected power loss, review the regulator’s datasheet, and verify that the device meets the electrical and thermal requirements of the complete circuit.

 

محوّل Buck أم منظّم الجهد LDO: كيف تختار الأنسب لمشروعك؟

قائمة المحتويات
  1. مقدمة.
  2. ما منظّم الجهد؟
  3. ما محوّل Buck؟
  4. ما منظّم الجهد LDO؟
  5. ما الفرق بين محوّل Buck ومنظّم LDO؟
  6. فهم القدرة والكفاءة وتوليد الحرارة.
  7. ضوضاء الخرج واستقرار الجهد.
  8. جهد الدخل وتيار الخرج وجهد السقوط.
  9. مزايا وقيود كل منظّم.
  10. متى تختار محوّل Buck؟
  11. متى تختار منظّم LDO؟
  12. هل يمكن استخدام محوّل Buck ومنظّم LDO معًا؟
  13. أمثلة عملية وحسابات تطبيقية
  14. كيف تختار منظّم الجهد المناسب لمشروعك؟
  15. أخطاء شائعة يجب تجنّبها.
  16. الأسئلة الشائعة.
  17. الخلاصة.

مدة القراءة: 20 دقيقة.

1. مقدمة

يُعد اختيار منظّم الجهد المناسب خطوة أساسية عند تصميم الدوائر الإلكترونية. فالمتحكّمات الدقيقة وأجهزة الاستشعار ووحدات الاتصال وغيرها من المكوّنات الإلكترونية تحتاج غالبًا إلى جهد تغذية مستمر وثابت، مثل 5V أو 3.3V أو 1.8V، حتى عندما يكون جهد مصدر الطاقة المتاح مختلفًا عن الجهد المطلوب.

من الحلول الشائعة لهذه المهمة محوّل Buck ومنظّم الجهد منخفض السقوط (LDO). يستطيع كلاهما خفض جهد تيار مستمر إلى جهد أقل ومنظّم، لكنهما يعتمدان على آليتَي تشغيل مختلفتين، ولكل منهما مزايا تجعله مناسبًا لتطبيقات محددة.

يعتمد محوّل Buck على التبديل الإلكتروني عالي السرعة ومكوّنات تخزين الطاقة لتحويل الجهد بكفاءة. أما منظّم LDO فهو نوع من منظّمات الجهد الخطية، يتحكّم في عنصر تمرير داخلي للمحافظة على جهد الخرج المطلوب، حتى عندما يكون جهد الدخل أعلى قليلًا من جهد الخرج.

مقارنة بين محوّل Buck ومنظّم الجهد LDO في الدوائر الإلكترونية

لا يُعد أيٌّ من الخيارين الأفضل في جميع الحالات. غالبًا ما يكون محوّل Buck هو الخيار الأنسب عندما تكون الكفاءة العالية وتقليل الحرارة من الأولويات، خصوصًا عند التيارات المرتفعة أو عند وجود فرق كبير بين جهدي الدخل والخرج. أما منظّم LDO، فيناسب عادةً الدوائر منخفضة التيار والتصميمات البسيطة والتطبيقات التي تتطلب ضوضاء منخفضة عند الخرج.

يشرح هذا المقال طريقة عمل كلا المنظّمين، ويقارن بينهما من حيث الكفاءة وتوليد الحرارة والضوضاء والقيود التشغيلية، كما يقدّم حسابات عملية تساعد المبتدئين والهواة والمهندسين على اختيار الحل المناسب لمشروعاتهم.

2. ما منظّم الجهد؟

منظّم الجهد هو دائرة أو جهاز إلكتروني يحافظ على جهد خرج ثابت نسبيًا رغم التغيّرات في جهد الدخل أو تيار الحمل، ما دام يعمل ضمن الحدود المحددة في مواصفاته.

أنواع منظّمات الجهد المستخدمة في الدوائر الإلكترونية

على سبيل المثال، قد يحتاج متحكّم دقيق إلى جهد تغذية قدره 3.3V، بينما يوفّر مصدر الطاقة المتاح جهدًا قدره 12V. يستطيع منظّم الجهد المناسب تحويل جهد الدخل البالغ 12V إلى خرج ثابت قدره 3.3V.

تنقسم منظّمات الجهد عمومًا إلى فئتين رئيسيتين:

  • منظّمات الجهد الخطية: تنظّم الجهد من خلال التحكّم في ترانزستور تمرير. وتنتمي منظّمات LDO إلى هذه الفئة.
  • منظّمات الجهد التبديلية: تستخدم ترانزستورات التبديل ومكوّنات تخزين الطاقة لتحويل القدرة الكهربائية بكفاءة. ويُعد محوّل Buck أحد أنواعها.

يعتمد اختيار المنظّم المناسب على جهد الدخل، وجهد الخرج المطلوب، وتيار الحمل، والحرارة التي يمكن تحمّلها، ومتطلبات الضوضاء، والمساحة المتاحة في التصميم.

3. ما محوّل Buck؟

محوّل Buck هو محوّل تبديل من تيار مستمر إلى تيار مستمر (DC-DC)، صُمّم لخفض جهد دخل مستمر أعلى إلى جهد خرج أقل.

على سبيل المثال، يمكن لمحوّل Buck تحويل 12V إلى 5V أو تحويل 5V إلى 3.3V مع تحقيق كفاءة جيدة عند تصميم الدائرة واختيار مكوّناتها بصورة صحيحة.

محوّل Buck خافض للجهد في تطبيق إلكتروني

كيف يعمل محوّل Buck؟

يتكوّن محوّل Buck التقليدي من ترانزستور للتبديل، وملف حثّي، ومكثّفات، بالإضافة إلى دايود أو ترانزستور تبديل متزامن.

تمرّ آلية عمله بمرحلتين أساسيتين:

  1. مرحلة التوصيل (ON): عندما يكون ترانزستور التبديل في حالة توصيل، تتدفّق الطاقة من مصدر الدخل عبر الملف الحثّي إلى الحمل، ويخزّن الملف جزءًا من الطاقة في مجاله المغناطيسي.
  2. مرحلة الإيقاف (OFF): عندما يتوقف الترانزستور عن التوصيل، يواصل الملف الحثّي تمرير التيار إلى الحمل عبر دايود الاستمرار أو ترانزستور التبديل المتزامن.

تتكرر المرحلتان بسرعة كبيرة. ويعمل الملف الحثّي والمكثّفات على تنعيم الموجة الكهربائية الناتجة، بينما تضبط دائرة التحكّم ذات التغذية الراجعة عملية التبديل للمحافظة على جهد الخرج المطلوب.

فهم دورة التشغيل (Duty Cycle)

تشير دورة التشغيل (D) إلى نسبة زمن التوصيل الذي يكون خلاله ترانزستور التبديل الرئيسي في حالة ON إلى الزمن الكلي لدورة التبديل.

في محوّل Buck مثالي يعمل في نمط التوصيل المستمر، يمكن التعبير عن العلاقة بين جهد الدخل والخرج كما يلي:

Vout = Vin × D

حيث:

  • Vout: جهد الخرج.
  • Vin: جهد الدخل.
  • D: دورة التشغيل، وتُعبّر عنها بقيمة بين 0 و1.

على سبيل المثال، إذا كان جهد الدخل 12V وكانت دورة التشغيل 0.5، فإن جهد الخرج النظري يساوي:

Vout = 12 × 0.5 = 6V

هذا حساب مثالي مبسّط. أما جهد الخرج الفعلي فيعتمد على متحكّم التغذية الراجعة، وفواقد المكوّنات، ونمط التشغيل، وعوامل التصميم الأخرى.

وحدات محوّلات Buck الشائعة

تُستخدم العديد من الدوائر المتكاملة ووحدات محوّلات Buck الجاهزة في المشروعات الإلكترونية، ومن أشهرها:

  • LM2596: منظّم تبديل خافض للجهد، يتوفر في وحدات عديدة ذات خرج قابل للضبط.
  • XL4015: منظّم تبديل يُستخدم في وحدات خفض الجهد المصمّمة لتيارات أعلى، مع مراعاة الحدود الكهربائية والحرارية للوحدة.
  • MP1584: دائرة متكاملة صغيرة لمحوّل Buck، تُستخدم في وحدات DC-DC المدمجة.

عند اختيار وحدة مناسبة، تحقّق من نطاق جهد الدخل، وتيار الخرج المقنن، والكفاءة، والأداء الحراري، ومتطلبات التبريد. فقد لا يكون التيار الأقصى المعلن قابلًا للاستمرار عمليًا من دون تبديد حراري كافٍ.

4. ما منظّم الجهد LDO؟

منظّم LDO، وهو اختصار لعبارة Low-Dropout Regulator، نوع من منظّمات الجهد الخطية يستطيع المحافظة على جهد خرج منظّم عندما يكون الفرق بين جهد الدخل والخرج صغيرًا نسبيًا.

على سبيل المثال، يمكن لمنظّم LDO مناسب تحويل 3.6V إلى 3.3V لتغذية مستشعر أو متحكّم دقيق أو دائرة تناظرية.

منظّم الجهد منخفض السقوط LDO المستخدم في الدوائر الإلكترونية

كيف يعمل منظّم LDO؟

يتكوّن منظّم LDO عادةً من مرجع للجهد، ومضخّم خطأ، وشبكة تغذية راجعة، وترانزستور تمرير.

تراقب دائرة التغذية الراجعة جهد الخرج باستمرار وتقارنه بجهد مرجعي داخلي. ثم يضبط مضخّم الخطأ عمل ترانزستور التمرير لتصحيح أي انحرافات والمحافظة على جهد الخرج المطلوب.

على عكس محوّل Buck، لا يستخدم منظّم LDO عملية تبديل عالية التردد لنقل الطاقة. بل يعمل ترانزستور التمرير في المنطقة الخطية، ويتحوّل فرق الجهد الزائد إلى حرارة.

ولكي يحافظ منظّم LDO على تنظيم الجهد، يجب أن يظل جهد الدخل أعلى من جهد الخرج بمقدار يكفي لتلبية متطلبات جهد السقوط الخاصة به.

فهم جهد السقوط (Dropout Voltage)

جهد السقوط هو أقل فرق مطلوب بين جهد الدخل وجهد الخرج حتى يتمكّن منظّم LDO من المحافظة على التنظيم المحدد في ظروف تشغيل معيّنة.

على سبيل المثال، إذا كان منظّم LDO يتطلب جهد سقوط قدره 200mV وكان جهد الخرج المطلوب 3.3V، فيجب أن يبقى جهد الدخل عند القيمة التالية أو أعلى منها:

Vin ≥ Vout + Vdropout

Vin ≥ 3.3 + 0.2 = 3.5V

تعتمد قيمة جهد السقوط الفعلية على طراز المنظّم وتيار الحمل ودرجة الحرارة. لذلك، راجع دائمًا ورقة البيانات الصادرة عن الشركة المصنّعة، ولا تفترض أن جميع منظّمات LDO لها القيمة نفسها.

نماذج شائعة لمنظّمات LDO

من أمثلة منظّمات LDO المستخدمة في الدوائر الإلكترونية:

  • AMS1117: عائلة من منظّمات الجهد الخطية تتوفر بإصدارات متعددة لجهد الخرج، وتُستخدم بكثرة في لوحات التطوير ووحدات تنظيم الجهد.
  • MCP1700: منظّم LDO منخفض تيار السكون، يناسب العديد من تطبيقات الطاقة المنخفضة.
  • AP2112K: منظّم LDO مدمج يُستخدم في تطبيقات متعددة لمصادر التغذية بجهد 3.3V و5V.

تختلف هذه الأجهزة في أقصى جهد دخل، وتيار الخرج، وجهد السقوط، وتيار السكون، والحدود الحرارية، ومتطلبات المكثّفات. لذلك، اختر الطراز الذي يتوافق مع احتياجات الدائرة وظروف تشغيلها.

5. ما الفرق بين محوّل Buck ومنظّم الجهد LDO؟

على الرغم من أن كلا الجهازين يستطيع توفير جهد خرج مستمر أقل ومنظّم، فإن الاختلاف في طريقة عملهما الداخلية يؤثر في الكفاءة، وتوليد الحرارة، والضوضاء، ومدى تعقيد الدائرة.

مقارنة بين محوّل Buck ومنظّم الجهد LDO

وجه المقارنة محوّل Buck منظّم LDO
طريقة تنظيم الجهد التبديل الإلكتروني عالي التردد ترانزستور تمرير يعمل في المنطقة الخطية
خفض الجهد نعم نعم
الكفاءة المعتادة غالبًا مرتفعة، بحسب ظروف التشغيل تتأثر بدرجة كبيرة بنسبة جهد الدخل إلى جهد الخرج
توليد الحرارة أقل عمومًا عند خفض الجهد بمقدار كبير قد يكون مرتفعًا عند وجود فرق كبير بين الجهدين أو تيار حمل مرتفع
تموّج جهد الخرج قد يظهر تموّج ناتج عن التبديل لا يولّد عادةً تموّج التبديل داخليًا
التداخل الكهرومغناطيسي يتطلب اهتمامًا بتصميم اللوحة والترشيح عادةً ما يكون أقل من ناحية التداخل المرتبط بالتبديل
تعقيد الدائرة أعلى نسبيًا أقل عادةً
المكوّنات الخارجية عادةً ملف حثّي ومكثّفات ومكوّنات تبديل عادةً مكثّفات عند الدخل والخرج
الأداء عند الحمل الخفيف يعتمد على نمط التشغيل وفواقد تيار السكون قد يكون ممتازًا في الطرازات ذات تيار السكون المنخفض
الاستخدام الأنسب تحويل الطاقة بكفاءة، خصوصًا عند الأحمال المرتفعة تنظيم بسيط للجهد، وتغذية منخفضة الضوضاء، وفروق جهد صغيرة

غالبًا ما يكون محوّل Buck الخيار الأفضل عندما تحتاج الدائرة إلى توفير قدرة كبيرة بكفاءة عالية. أما منظّم LDO، فقد يكون أنسب عندما يكون فرق الجهد صغيرًا، أو يكون تيار الحمل منخفضًا، أو تكون متطلبات الضوضاء هي العامل الأهم. ولا يتفوّق أي منهما تلقائيًا في جميع التطبيقات.

6. فهم القدرة والكفاءة وتوليد الحرارة

تُعد كفاءة الطاقة والحرارة الناتجة من أهم العوامل التي ينبغي مراعاتها عند اختيار منظّم الجهد.

توضيح القدرة والكفاءة وفقد الطاقة على شكل حرارة في منظّمات الجهد

قدرة الخرج

يمكن حساب قدرة الخرج بضرب جهد الخرج في تيار الخرج:

Pout = Vout × Iout

على سبيل المثال، إذا كان جهد الخرج 5V وتيار الخرج 2A، فإن القدرة المطلوبة تساوي:

Pout = 5 × 2 = 10W

وهذا يعني أن الحمل يستقبل قدرة كهربائية مقدارها 10W.

فقد القدرة في منظّم LDO

في المنظّم الخطي، يمكن تقدير القدرة المفقودة التي تتحول إلى حرارة باستخدام المعادلة التالية:

Ploss = (Vin − Vout) × Iout

على سبيل المثال، عند خفض الجهد من 12V إلى 5V مع تيار حمل قدره 0.5A، يكون الفقد التقريبي في المنظّم:

Ploss = (12 − 5) × 0.5 = 3.5W

وفقًا لهذه الافتراضات، يجب على المنظّم تبديد نحو 3.5W على شكل حرارة. وتُعد هذه كمية كبيرة نسبيًا لمكوّن صغير، وقد تستلزم اختيار منظّم آخر أو تحسين التصميم الحراري أو الجمع بين الحلّين.

يفترض هذا الحساب المبسّط أن تيار الدخل يساوي تقريبًا تيار الخرج، ولا يحتسب تيار الأرضي الذي يستهلكه المنظّم. وللحصول على نتيجة أدق، استخدم قيمتي تيار الدخل والخرج الفعليتين.

كفاءة محوّل Buck

تُحسب كفاءة المنظّم من خلال نسبة قدرة الخرج إلى قدرة الدخل، وتُعبّر عنها كنسبة مئوية:

η = (Pout ÷ Pin) × 100%

لنفترض أن محوّل Buck يوفّر خرجًا بجهد 5V وتيار 0.5A، وأن كفاءته تبلغ 85%.

أولًا، نحسب قدرة الخرج:

Pout = 5 × 0.5 = 2.5W

ثم نحسب قدرة الدخل التقريبية:

Pin = Pout ÷ η

وبما أن الكفاءة 85%، نستخدم القيمة 0.85 في الحساب:

Pin = 2.5 ÷ 0.85 ≈ 2.94W

إذا كان جهد الدخل 3.7V، فإن تيار الدخل التقريبي يساوي:

Iin = Pin ÷ Vin

Iin = 2.94 ÷ 3.7 ≈ 0.79A

أما فقد القدرة التقريبي في المحوّل، فيُحسب بطرح قدرة الخرج من قدرة الدخل:

Ploss = Pin − Pout

Ploss = 2.94 − 2.5 = 0.44W

وبذلك، يبدّد المحوّل نحو 0.44W على شكل فقد في الطاقة وفقًا لظروف التشغيل المفترضة.

مقارنة توليد الحرارة

لنفترض أن لدينا جهد دخل 12V، وجهد خرج 5V، وتيار حمل 1A.

بالنسبة إلى منظّم LDO:

Ploss = (12 − 5) × 1 = 7W

أما محوّل Buck، بافتراض كفاءة تبلغ 90%:

Pin = 5 ÷ 0.90 ≈ 5.56W

Ploss = 5.56 − 5 = 0.56W

في هذا المثال، يبدّد منظّم LDO نحو 7W من القدرة على شكل حرارة، بينما يبلغ الفقد في محوّل Buck نحو 0.56W فقط. وهذا يوضّح لماذا يكون محوّل Buck غالبًا الخيار الأنسب عند خفض الجهد بمقدار كبير وتوفير تيار مرتفع.

هذه الأرقام أمثلة حسابية توضيحية وليست ضمانًا لأداء جميع الأجهزة. فالكفاءة الفعلية تعتمد على المنظّم المختار، وجهدي الدخل والخرج، والحمل، ودرجة الحرارة، وتصميم الدائرة.

7. ضوضاء الخرج واستقرار الجهد

تُعد ضوضاء الخرج عاملًا مهمًا أيضًا، خصوصًا في الدوائر التي تحتوي على مستشعرات تناظرية، أو دوائر صوتية، أو محوّلات تناظرية إلى رقمية (ADC)، أو محوّلات رقمية إلى تناظرية (DAC)، أو مكوّنات تعمل بالترددات الراديوية (RF).

مقارنة ضوضاء الخرج وتموّج الجهد بين محوّل Buck ومنظّم LDO

الضوضاء في محوّل Buck

يبدّل محوّل Buck ترانزستور القدرة بسرعة بين حالتي التوصيل (ON) والإيقاف (OFF). وينتج عن عملية التبديل تموّج في جهد الخرج، وقد يتولّد أيضًا تداخل كهرومغناطيسي (EMI).

يمكن تقليل الضوضاء باستخدام مكثّفات مناسبة، وتصميم جيد للوحة الدوائر المطبوعة (PCB)، وتقليل أطوال مسارات التيار المرتفع، واستخدام مرشّحات مصمّمة بعناية.

ومع ذلك، لا يُعد تموّج التبديل مشكلة في كل التطبيقات؛ إذ يمكن للعديد من الدوائر الرقمية العمل بصورة صحيحة عند استخدام محوّل Buck مصمّم جيدًا.

الضوضاء في منظّم LDO

لا يولّد منظّم LDO تموّج التبديل الدوري المرتبط بالمحوّلات التبديلية، ولذلك تكون العديد من منظّمات LDO مناسبة للدوائر الحسّاسة للضوضاء.

لكن منظّم LDO ليس خاليًا تمامًا من الضوضاء؛ إذ تولّد داراته الداخلية قدرًا من الضوضاء، كما تعتمد قدرته على رفض الضوضاء القادمة من مصدر التغذية على نسبة رفض اضطرابات مصدر الطاقة (PSRR)، وتردد التشغيل، والحمل، وظروف أخرى.

يمكن أن يكون منظّم LDO منخفض الضوضاء خيارًا مفيدًا لتغذية المكوّنات التناظرية الحسّاسة، بشرط استيفاء متطلبات الجهد والتيار والحرارة.

أيهما أفضل للإلكترونيات الحسّاسة؟

يعتمد الاختيار على متطلبات الضوضاء الفعلية للدائرة:

  • في حالة المتحكّم الدقيق الرقمي، قد يكون محوّل Buck مناسبًا إذا كان تصميمه جيدًا.
  • في حالة مستشعر تناظري حسّاس أو دائرة ترددات راديوية، قد يكون منظّم LDO منخفض الضوضاء خيارًا أفضل.
  • إذا كان التصميم يحتاج إلى كفاءة عالية وضوضاء منخفضة في الوقت نفسه، فقد يكون من المناسب استخدام محوّل Buck يتبعه منظّم LDO.

تحقّق دائمًا من مواصفات الضوضاء وPSRR الخاصة بمنظّم LDO عند الترددات المعنية، ولا تفترض أن كل منظّم LDO قادر على إزالة ضوضاء التبديل بالكامل.

8. جهد الدخل وتيار الخرج وجهد السقوط

قبل اختيار منظّم الجهد، تأكّد من أن حدوده الكهربائية تتوافق مع متطلبات التطبيق الذي تعمل عليه.

توضيح جهد الدخل وتيار الخرج وجهد السقوط عند اختيار منظّم الجهد

جهد الدخل وجهد الخرج
  • يجب أن يقع جهد الدخل ضمن نطاق التشغيل المحدد في مواصفات المنظّم.
  • يستطيع محوّل Buck خفض الجهد، لكنه لا يستطيع عادةً إنتاج جهد خرج منظّم أعلى من جهد دخله. إذا كان جهد الخرج المطلوب أعلى من جهد الدخل، ففكّر في استخدام محوّل رفع الجهد (Boost Converter).
  • يتطلب منظّم LDO أن يكون جهد الدخل أعلى من جهد الخرج المطلوب بمقدار لا يقل عن جهد السقوط اللازم في ظروف التشغيل المعنية.
  • على سبيل المثال، عند خفض الجهد من 3.5V إلى 3.3V باستخدام منظّم LDO يحتاج إلى جهد سقوط قدره 200mV، يكون هامش التشغيل محدودًا. وقد تؤدي تغيّرات جهد الدخل أو زيادة تيار الحمل إلى خروج المنظّم من نطاق تنظيم الجهد.
أقصى تيار للخرج
  • يجب أن يكون المنظّم قادرًا على توفير أقصى تيار يحتاج إليه الحمل، بما في ذلك الارتفاعات القصيرة في التيار التي قد تنتج عن وحدات الاتصال اللاسلكي أو المحرّكات أو غيرها من الأحمال المتغيّرة.
  • لا تعتمد على قيمة التيار القصوى المعلنة وحدها؛ بل تحقّق من الأداء الحراري، وحدود تحديد التيار، ومساحة النحاس في لوحة الدوائر المطبوعة، وقيود الحزمة الإلكترونية، وظروف التشغيل التي توصي بها الشركة المصنّعة.
تيار السكون وعمر البطارية

تيار السكون (IQ) هو التيار الذي يستهلكه المنظّم داخليًا لتشغيل دوائر التحكم الخاصة به. وتزداد أهمية هذه القيمة في الأجهزة التي تعمل بالبطاريات، خصوصًا عندما يقضي الحمل فترات طويلة في وضع السكون.

قد يحقق محوّل Buck كفاءة عالية عند الأحمال الكبيرة، لكن بعض الطرازات تستهلك تيارًا ملحوظًا أو تنخفض كفاءتها عند الأحمال الخفيفة جدًا. لذلك، قد يكون منظّم LDO منخفض تيار السكون خيارًا أفضل لجهاز منخفض الطاقة يقضي معظم وقته في وضع السكون.

قارن منحنيات الكفاءة الفعلية ومواصفات تيار السكون ضمن نطاق التشغيل المتوقع قبل اتخاذ القرار.

9. مزايا وعيوب كل نوع من منظمات الجهد

مزايا محول Buck
  • كفاءة عالية في العديد من تطبيقات خفض الجهد.
  • فقد أقل في القدرة الحرارية عند وجود فرق كبير بين جهد الدخل وجهد الخرج أو عند تشغيل أحمال مرتفعة التيار.
  • مناسب لتغذية المتحكمات الدقيقة ولوحات التطوير والشاشات وغيرها من الدوائر التي تحتاج إلى تيار مرتفع نسبيًا.
  • يمكن أن يطيل مدة تشغيل الأجهزة التي تعمل بالبطاريات عند اختياره وتصميمه بالشكل المناسب.
  • يدعم نطاقًا واسعًا من مستويات القدرة، وفقًا لنوع المكوّن وتصميم الدائرة.
عيوب محول Buck
  • يحتاج إلى عدد أكبر من المكونات وإلى تصميم دقيق للدائرة.
  • قد يؤثر التموج الناتج عن التبديل والتداخل الكهرومغناطيسي (EMI) في الدوائر الحساسة.
  • يمكن أن يؤثر تخطيط لوحة الدائرة المطبوعة (PCB) واختيار المكونات بشكل كبير في الأداء.
  • تتغير الكفاءة بحسب جهد الدخل وتيار الخرج وتردد التبديل ونمط التشغيل.
  • قد تزيد الملفات الحثية والمكونات الأخرى من الحجم الإجمالي للدائرة.
مزايا منظم LDO
  • سهل التنفيذ في الدوائر الإلكترونية.
  • يحتاج عادةً إلى عدد أقل من المكونات الخارجية.
  • يوفر غالبًا خرجًا قليل التموج، دون ضوضاء التبديل المرتبطة عادةً بالمحولات switching.
  • يوفر تنظيمًا جيدًا للجهد في دوائر القدرة المنخفضة.
  • قد يحقق أداءً جيدًا جدًا مع الأحمال الخفيفة عند استخدام طراز ذي تيار استهلاك داخلي منخفض.
  • يمكنه تنظيم الجهد عندما يكون جهد الدخل قريبًا من جهد الخرج، بشرط استيفاء متطلبات جهد السقوط.
عيوب منظم LDO
  • قد يولّد حرارة كبيرة عندما يكون الفرق بين جهد الدخل وجهد الخرج مرتفعًا.
  • تتأثر كفاءته بنسبة جهد الخرج إلى جهد الدخل، إضافةً إلى استهلاكه الداخلي للتيار.
  • يحتاج إلى فرق جهد كافٍ بين الدخل والخرج حتى يحافظ على التنظيم.
  • قد يحدّ التبديد الحراري من أقصى تيار خرج يمكنه توفيره.
  • تختلف متطلبات مكثفات الدخل والخرج وشروط استقرار الدائرة باختلاف الطراز.

10. متى تختار محول Buck؟

يُعد محول Buck خيارًا مناسبًا عندما يتطلب التطبيق خفض الجهد بكفاءة عالية.

محول Buck لخفض الجهد بكفاءة في الدوائر الإلكترونية

فكّر في استخدام محول Buck في الحالات التالية:

  • خفض الجهد من 12V إلى 5V أو من 5V إلى 3.3V عند الحاجة إلى تيار متوسط أو مرتفع.
  • تغذية أنظمة تعتمد على Arduino أو ESP8266 أو ESP32 أو Raspberry Pi من مصدر جهد أعلى، بشرط توافقه مع متطلبات اللوحة.
  • تشغيل الأجهزة التي تعمل بالبطاريات عندما تكون كفاءة استهلاك الطاقة عاملًا مهمًا.
  • تغذية الشاشات ووحدات الاتصال وغيرها من الأحمال التي تحتاج إلى تيار ملحوظ.
  • تقليل الحرارة داخل الأجهزة ذات المساحة المحدودة.

على سبيل المثال، عند استخدام مصدر 12V لتغذية حمل يحتاج إلى 5V وتيار 1A، يصبح محول Buck خيارًا جديرًا بالاهتمام. ففي هذه الحالة، سيبدّد منظم LDO نحو 7W من القدرة على هيئة حرارة، وفقًا للحسابات التقريبية الموضحة سابقًا.

قبل اختيار محول Buck، تحقّق من نطاق جهد الدخل، وقدرة تيار الخرج، والكفاءة، وتموج جهد الخرج، وتردد التبديل، والأداء الحراري.

11. متى تختار منظم LDO؟

يكون منظم LDO مناسبًا غالبًا عندما تكون بساطة التصميم أو انخفاض الضوضاء أو صِغر الفرق بين جهد الدخل والخرج أهم من تحقيق أعلى كفاءة ممكنة.

منظم الجهد الخطي LDO لتغذية الدوائر الإلكترونية الحساسة

فكّر في استخدام منظم LDO في الحالات التالية:

  • خفض الجهد من 3.6V إلى 3.3V في دائرة ذات استهلاك منخفض للتيار.
  • تغذية المستشعرات التناظرية الحساسة أو دوائر الجهد المرجعي.
  • توفير جهد تغذية منخفض الضوضاء لمحوّلات ADC أو DAC أو مكونات الترددات الراديوية (RF).
  • تصميم دائرة بسيطة منخفضة القدرة مع مساحة محدودة للمكونات الخارجية.
  • تغذية جهاز يعمل بالبطارية ويستهلك تيارًا منخفضًا، خصوصًا عندما يقضي فترات طويلة في وضع السكون.

على سبيل المثال، عند خفض الجهد من 3.6V إلى 3.3V مع تيار خرج يبلغ 100mA، يمكن تقدير القدرة المفقودة في منظم LDO كما يلي:

Ploss = (3.6 − 3.3) × 0.1 = 0.03W

أي إن المنظم يبدّد نحو 30mW من القدرة على هيئة حرارة، وهي كمية صغيرة نسبيًا.

مع ذلك، تحقّق من جهد السقوط، وتيار الاستهلاك الداخلي، وأقصى جهد دخل، وتصنيف تيار الخرج، ومتطلبات المكثفات قبل اختيار المنظم.

12. هل يمكن استخدام محول Buck ومنظم LDO معًا؟

نعم، يُعد توصيل الجهازين على التوالي أسلوبًا شائعًا في تصميم مصادر الطاقة، ويُعرف باسم التنظيم اللاحق (Post-Regulation).

في هذا الترتيب، يتولى محول Buck خفض الجهد الأساسي بكفاءة، ثم يوفّر منظم LDO تنظيمًا إضافيًا للجهد، وقد يساعد على تقليل الضوضاء التي تصل إلى الحمل الحساس.

يمكن أن يكون ترتيب الدائرة على النحو التالي:

12V Input → Buck Converter → 3.6V Intermediate Supply → LDO → 3.3V Output

يخفض محول Buck فرق الجهد الكبير، بينما يتولى منظم LDO ضبط جهد الخرج النهائي.

توصيل محول Buck مع منظم LDO للحصول على خرج مستقر ومنخفض الضوضاء

فوائد استخدام الجهازين معًا
  • تحقيق كفاءة إجمالية أفضل من استخدام منظم LDO وحده لخفض الجهد بمقدار كبير، في العديد من التطبيقات.
  • إمكانية تقليل تموج جهد الخرج والضوضاء.
  • تحسين جودة التغذية الكهربائية للدوائر التناظرية الحساسة ودوائر الترددات الراديوية.
  • توفير مرونة أكبر عند تصميم خطوط تغذية منفصلة للدوائر الرقمية والتناظرية.
اعتبارات مهمة عند التصميم

يجب أن يكون جهد الدخل إلى منظم LDO أعلى من جهد الخرج بما يكفي للحفاظ على التنظيم، كما يجب أن يظل التبديد الحراري ضمن الحدود الآمنة.

على سبيل المثال، إذا خفّض منظم LDO الجهد من 3.6V إلى 3.3V عند تيار 100mA، فإن القدرة المفقودة تُحسب تقريبًا كما يلي:

Ploss = (3.6 − 3.3) × 0.1 = 0.03W

تبلغ الخسارة نحو 0.03W فقط، بينما يتولى محول Buck خفض الجهد الأساسي، ما يساعد على تقليل الحرارة الناتجة عن عملية التنظيم النهائية.

كذلك، يجب التحقق من مواصفة نسبة رفض مصدر التغذية (PSRR) لمنظم LDO عند تردد التبديل الخاص بمحول Buck. فلا يضمن استخدام LDO إزالة جميع أنواع ضوضاء التبديل، خصوصًا عند الترددات العالية.

13. أمثلة عملية وحسابات تطبيقية

توضح الأمثلة التالية كيفية تطبيق معايير الاختيار عند استخدام منظمات الجهد في مشروعات إلكترونية شائعة.

المثال الأول: تشغيل ESP32 باستخدام مصدر طاقة بجهد 12 فولت

لنفترض أننا نحتاج إلى توفير جهد ثابت قدره 3.3 فولت لدائرة تعتمد على ESP32، وتسحب تيارًا مقداره 500 ملي أمبير، باستخدام مصدر طاقة بجهد 12 فولت.

يمكن حساب قدرة الخرج كما يلي:

Pout = Vout × Iout

Pout = 3.3 × 0.5 = 1.65W

إذا استخدمنا منظم جهد خطيًا من نوع LDO، فسيكون الفقد التقريبي في القدرة:

Ploss = (12 − 3.3) × 0.5 = 4.35W

هذه كمية كبيرة من الحرارة، ولذلك يكون محول خافض للجهد من نوع Buck Converter خيارًا أفضل عادةً عند التعامل مع هذا الفرق في الجهد والتيار.

عمليًا، اختر محولًا يتحمل أقصى جهد متوقع من مصدر الطاقة، وتيار الذروة الذي قد تحتاج إليه لوحة ESP32، وأي أحمال إضافية في الدائرة. لا توصل جهد 12 فولت مباشرةً بمدخل التغذية المخصص لجهد 3.3 فولت.

المثال الثاني: تشغيل مستشعر بجهد 3.3 فولت من مصدر بجهد 3.6 فولت

لنفترض أن مستشعرًا يحتاج إلى جهد 3.3 فولت وتيار 50 ملي أمبير، بينما يبلغ جهد مصدر الطاقة المتاح 3.6 فولت.

يمكن حساب الفقد التقريبي في القدرة داخل منظم LDO كما يلي:

Ploss = (3.6 − 3.3) × 0.05 = 0.015W

أي أن القدرة المفقودة تبلغ 15 ملي واط فقط، ولذلك يكون توليد الحرارة محدودًا في هذه الظروف.

قد يكون منظم LDO خيارًا عمليًا هنا، لأن الفرق بين جهدي الدخل والخرج صغير، وكذلك التيار المطلوب. ومع ذلك، يجب التأكد من أن جهد الإسقاط (Dropout Voltage) للمنظم منخفض بما يكفي للحفاظ على استقرار الخرج ضمن نطاق جهد الدخل الكامل.

المثال الثالث: تغذية دائرة تناظرية حساسة
  • لنفترض أن مستشعرًا تناظريًا يحتاج إلى جهد تغذية ثابت قدره 3.3 فولت، وأن دقة قياساته تتأثر بضوضاء مصدر الطاقة.
  • يمكن استخدام منظم LDO منخفض الضوضاء إذا كان جهد الدخل قريبًا بما يكفي من 3.3 فولت، وكان تيار الحمل ضمن الحدود المسموح بها.
  • هناك خيار آخر يتمثل في استخدام محول Buck لخفض جهد المصدر الرئيسي، ثم توصيل منظم LDO بعده للحصول على تنظيم إضافي وتقليل بعض الضوضاء والتموجات.
  • يعتمد الاختيار الأنسب على مدى حساسية المستشعر للضوضاء، وقدرة المنظم على رفض التموجات (PSRR) عند الترددات المطلوبة، والتيار اللازم، والقدرة المتاحة في النظام.

14. كيف تختار منظم الجهد المناسب لمشروعك؟

معايير اختيار منظم الجهد المناسب للمشروعات الإلكترونية

استخدم قائمة التحقق التالية عند اختيار منظم جهد لتصميم إلكتروني جديد.

  1. تحديد نطاق جهد الدخل: ضع في الحسبان الحدين الأدنى والأقصى لجهد التغذية، وانخفاض جهد البطارية أثناء التفريغ، وأي ارتفاعات مفاجئة محتملة في الجهد.
  2. تحديد جهد الخرج المطلوب: تأكد من توافقه مع نطاق الجهد المسموح به للمكونات التي سيغذيها المنظم.
  3. حساب أقصى تيار للحمل: لا تكتفِ بتيار التشغيل المعتاد؛ بل احسب أيضًا تيار بدء التشغيل والارتفاعات اللحظية في التيار.
  4. تقدير فقد القدرة والحرارة: في منظم LDO، استخدم فرق الجهد بين الدخل والخرج وتيار الحمل. أما في محول Buck، فيمكن تقدير الفقد اعتمادًا على كفاءته.
  5. تقييم متطلبات الضوضاء: ضع في الحسبان تموجات الخرج، والتداخل الكهرومغناطيسي (EMI)، والضوضاء الداخلية للمنظم، وقدرته على رفض اضطرابات جهد الدخل (PSRR).
  6. مراجعة أداء البطارية: قارن التيار الداخلي الذي يستهلكه المنظم وكفاءته أثناء التشغيل العادي وفي وضع الاستعداد.
  7. التحقق من الحدود الكهربائية والحرارية: راجع ورقة البيانات الخاصة بالشركة المصنعة، وحدود الحزمة الإلكترونية، وظروف التشغيل الموصى بها.
  8. مراعاة التكلفة وتعقيد الدائرة: احسب تكلفة المكونات الخارجية، ومتطلبات تصميم لوحة الدائرة المطبوعة (PCB)، والحاجة إلى مرشحات إضافية.
دليل سريع لاختيار منظم الجهد
التطبيق الخيار الموصى به مبدئيًا
التحويل من 12 فولت إلى 5 فولت عند 1 أمبير محول Buck خافض للجهد
التحويل من 5 فولت إلى 3.3 فولت عند تيار مرتفع غالبًا محول Buck
التحويل من 3.6 فولت إلى 3.3 فولت عند تيار منخفض منظم LDO، إذا سمح جهد الإسقاط بذلك
تغذية دائرة تناظرية تحتاج إلى ضوضاء منخفضة منظم LDO منخفض الضوضاء، أو محول Buck يتبعه منظم LDO
جهاز يعمل بالبطارية ويحتاج إلى تيار استعداد منخفض جدًا مقارنة مواصفات التيار الداخلي والكفاءة لمنظمي Buck وLDO
خفض كبير للجهد مع إمكانات محدودة لتبديد الحرارة غالبًا محول Buck

تمثل هذه التوصيات نقطة بداية وليست قواعد مطلقة. فالاختيار النهائي يعتمد على مواصفات المنظم الفعلي، وظروف التشغيل، ومتطلبات التطبيق.

15. أخطاء شائعة ينبغي تجنبها

الاختيار بناءً على أقصى تيار فقط

قد لا يتمكن منظم مُعلن عن قدرته على توفير تيار 1 أمبير من تقديم هذا التيار بصورة مستمرة في جميع الدوائر. فقد تحدّ القيود الحرارية، وتصميم لوحة الدائرة المطبوعة، وحجم الحزمة الإلكترونية، ودرجة الحرارة المحيطة من التيار الفعلي الذي يمكن استخدامه بأمان.

افتراض أن جميع منظمات LDO منخفضة الضوضاء

تختلف منظمات LDO في مقدار الضوضاء الناتجة عن دوائرها الداخلية، وفي قدرتها على رفض التموجات القادمة من مصدر الطاقة. لذلك، راجع المواصفات الفعلية في ورقة البيانات، بما في ذلك نطاق ترددات قياس الضوضاء ونطاق التردد الذي تم تحديد PSRR عنده.

تجاهل جهد الإسقاط

قد يعجز منظم LDO عن الحفاظ على جهد الخرج المطلوب عندما يقترب جهد الدخل من جهد الخرج أكثر مما تسمح به مواصفاته. تحقق من قيمة جهد الإسقاط عند تيار الحمل ودرجة الحرارة المتوقعين.

افتراض أن محول Buck أكثر كفاءة دائمًا

تتعرض محولات Buck لفواقد ناتجة عن التبديل، كما تستهلك دوائرها الداخلية قدرًا من التيار. وعند الأحمال الخفيفة جدًا، أو عندما يكون الفرق بين جهد الدخل والخرج صغيرًا، قد يكون منظم LDO أكثر كفاءة في بعض الظروف.

إهمال تبديد الحرارة

احسب الفقد المتوقع في القدرة، وتأكد من قدرة المكوّن على تبديد الحرارة الناتجة بأمان. لا تفترض أن منظمًا صغيرًا يستطيع التعامل مع عدة واطات من الحرارة دون تصميم حراري مناسب.

تجاهل متطلبات المكثفات وتصميم لوحة الدائرة

اتبع توصيات الشركة المصنعة بشأن مكثفات الدخل والخرج. وفي محولات Buck، انتبه بصورة خاصة إلى مسارات التيار المتبدل، والتأريض، وتصميم لوحة الدائرة المطبوعة. أما في منظمات LDO، فتحقق من متطلبات مكثف الخرج وشروط استقرار المنظم.

16. الأسئلة الشائعة

هل محول Buck أفضل من منظم LDO؟

ليس في جميع الحالات. يكون محول Buck أفضل عادةً عند الحاجة إلى خفض الجهد بكفاءة، خصوصًا عندما يكون فرق الجهد كبيرًا أو يكون تيار الحمل مرتفعًا. أما منظم LDO فقد يكون أنسب للدوائر التي تحتاج إلى ضوضاء منخفضة وتيار محدود، أو عندما يكون الفرق بين جهدي الدخل والخرج صغيرًا.

هل يستطيع منظم LDO تحويل 12 فولت إلى 5 فولت؟

نعم، بشرط أن يتحمل المنظم المختار جهد الدخل وتيار الحمل المطلوبين. لكن عند تيار 1 أمبير، يبلغ الفقد التقريبي في القدرة:

Ploss = (12 − 5) × 1 = 7W

قد تؤدي هذه الكمية من الحرارة إلى ارتفاع مفرط في درجة حرارة المكوّن، خصوصًا إذا كان صغير الحجم. لذلك يكون محول Buck أنسب عادةً لهذا التطبيق.

هل يوفر محول Buck جهد خرج ثابتًا؟

نعم. يستخدم محول Buck المصمم بصورة صحيحة دائرة تحكم للحفاظ على جهد الخرج وتنظيمه رغم تغير جهد الدخل وتيار الحمل، ضمن نطاق التشغيل المحدد له. ومع ذلك، قد تظهر بعض التموجات في جهد الخرج، ويعتمد مقدارها على تصميم المحول ومكوناته.

لماذا تُستخدم منظمات LDO بعد محولات Buck؟

يمكن لمنظم LDO توفير تنظيم إضافي وتقليل جزء من التموجات والضوضاء القادمة من محول التبديل السابق له. وقد يكون ذلك مفيدًا عند تغذية الدوائر التناظرية الحساسة ودوائر الترددات اللاسلكية، بشرط توفر فرق جهد كافٍ بين الدخل والخرج.

أي المنظمين أفضل للمشروعات التي تعمل بالبطارية؟

يعتمد ذلك على نطاق جهد البطارية، وتيار الحمل، ومتطلبات وضع الاستعداد. قد يوفر محول Buck كفاءة أعلى عند الأحمال الكبيرة، بينما يكون منظم LDO ذي التيار الداخلي المنخفض خيارًا مناسبًا للتطبيقات منخفضة الاستهلاك، أو عندما يكون جهد الدخل قريبًا من جهد الخرج.

هل يمكن استخدام محول Buck لزيادة الجهد؟

لا. صُمم محول Buck التقليدي لخفض الجهد. إذا كنت تحتاج إلى جهد خرج أعلى من جهد الدخل، فاستخدم محول Boost رافع للجهد، أو محول Buck-Boost مناسبًا للتطبيق.

كيف يمكن حساب القدرة المفقودة في منظم الجهد؟

في منظم LDO، يمكن استخدام العلاقة التقريبية التالية:

Ploss = (Vin − Vout) × Iout

أما في محول التبديل، فعندما تكون الكفاءة معروفة، يمكن حساب الفقد التقريبي كما يلي:

Ploss = Pout × (1 ÷ η − 1)

يرمز η إلى الكفاءة بصيغة عشرية؛ فعلى سبيل المثال، تُمثَّل كفاءة 90% بالقيمة 0.90.

ما المواصفات التي ينبغي مراجعتها قبل شراء منظم الجهد؟

تحقق من نطاق جهد الدخل، وجهد الخرج، وأقصى تيار خرج، والكفاءة، وجهد الإسقاط عند استخدام منظم LDO، والأداء الحراري، والتيار الداخلي، وضوضاء الخرج، ومتطلبات المكثفات، وخصائص الحماية المتوفرة.

17. الخلاصة

يتطلب الاختيار بين محول Buck ومنظم الجهد LDO تحقيق توازن بين الكفاءة، وتوليد الحرارة، وضوضاء الخرج، وتعقيد الدائرة، ومتطلبات الحمل.

يُعد محول Buck الخيار الأنسب غالبًا للتطبيقات التي تتطلب خفضًا كبيرًا للجهد، أو تيارًا مرتفعًا، أو كفاءة عالية في استهلاك الطاقة. أما منظم LDO، فيناسب عادةً الدوائر منخفضة التيار، والتطبيقات التي يكون فيها فرق الجهد صغيرًا، والدوائر الحساسة للضوضاء.

إذا كان التصميم يحتاج إلى كفاءة عالية مع جهد تغذية منخفض الضوضاء، فإن الجمع بين محول Buck ومنظم LDO مناسب قد يوفر حلًا عمليًا يجمع بين ميزات النوعين.

وأفضل طريقة لاتخاذ القرار هي حساب الفقد المتوقع في القدرة، ومراجعة ورقة البيانات الخاصة بالمنظم، والتحقق من توافق مواصفاته الكهربائية والحرارية مع متطلبات الدائرة كاملة.

Shop: Need a DC-DC converter, a voltage regulator or a power adapter? See DC-DC converters and power supplies in Egypt and see what is in stock at Makers Electronics.

Leave a comment